Bullard Tacsight Bedienungsanleitung PDF herunterladen

Bullard TACSIGHT Accessories

User Manual

www.bullard.com

TACPort™

Bullard offers the TACPort as a power accessory to the TACSIGHT

Thermal Imager. Electrical outputs on the TACPort allow for

easy connection to external power sources, and the video

output can be connected to a transmitter, remote display,

or video recorder. Used in conjunction with the TACSIGHT

thermal imager, the TACPort provides the user extended

surveillance time and operating flexibility.

Connecting to the TACSIGHT Thermal Imager

To connect the TACPort to the TACSIGHT thermal imager, place the TACPort against the bottom

of the thermal imager so that the thumbscrew on the TACPort aligns with the thermal imager's

tripod socket, and the TACPort label is to the rear of the thermal imager. Turn the thumbscrew

until firmly secure. Electrical and video connections are made automatically once the TACPort is

attached.

Powering the TACPort

Two DC ports are located on the side of the TACPort, allowing the user to either input power into

the camera or to draw out power to various accessories. If used to input power, voltage should

be 12-15 VDC, center positive on a 2.5 mm phone plug. A standard DC cigarette lighter adapter

is provided, which can be used with any standard 12 volt vehicle outlet or separate battery

source.

When an external power source is used, the thermal imager's power switch and battery LEDs

are bypassed. The thermal imager will remain on as long as this external power supply is

connected to the thermal imager. If a battery is connected to the thermal imager, it will still

operate off the external source, but the LED charge indicators on the thermal imager will not be

accurate.

NOTE

The external power supply will not charge the thermal imager.

Powering an Accessory from the TACPort

The TACPort is designed to power accessories through the TACSIGHT thermal imager or through

an external pow

er suppl

. If using an external pow

er suppl

y, the output voltage is the same as

the v

oltage provided b

y the external power supply. Whether the thermal imager is ON or OFF, it

is continually providing output power when connected to an external power supply. If there is no

external power supply, the voltage output will be from the thermal imager battery, ranging from

8.5 to 11.0 VDC. When using this battery source only, the thermal imager must be on to provide

output power.

NOTE

Using the thermal imager battery to power accessories will shorten the charge life

of the battery

, thus decreasing the operating time of the accessory

. Use an external

power supply whenever possible. When using any accessory, the user should

verify th

at any accessory powered from the TACPort is compatible with the voltage

supplied and is saf

e to operate at v

oltages from 10 to 15 VDC

ideo output is a standard NTSC television signal. The connector is type BNC, and an adapter is

provided to permit use of an RCA type video cable connection.

NOTE

There is no video input on the TACPort.

TACPort Specifications

Power In: Voltage 10 - 15VDC Current 1.0A minimum

Power Out: Voltage 10 - 15VDC (depends on power in source and/or battery in

imager)

Power Connector: 2.5mm phone plug, center positive (Cable provided for vehicle

cigarette lighter connection)

Video Out: NTSC video signal

Video Connector: BNC (Adapter provided for RCA cable connection)

Tripod Mount: 1/4"-20 standard tripod thread

Water Resistance: IP64

Shock Resistance: 1 Meter drop on concrete

Temperature:- 20 - +80 C

NOTE

The TACPort cannot be used in conjunction with the TACScope or HANDLEVO

Accessories.

TACScope™

The Bullard TACScope is a micro display eyepiece that can be

quickly and easily attached to the TACSIGHT thermal

imager. In conjunction with the optional display shutoff on

the TACSIGHT, the TACScope allows discreet nighttime

surveillance by eliminating the display as a light source. A rubber

eyecup on the TACScope prevents illumination of the face by stray

light from the eyepiece.

TACScope

To connect the TACScope to the TACSIGHT thermal imager, align the screw on the bottom of the

TACScope with the tripod socket on the bottom of the thermal imager (making sure the rubber

eyecup is to the rear of the camera), and tighten the thumbscrew until secure. When fully

secured, the TACScope is electrically connected and is operable whenever the thermal imager is

on.

Using the TACScope

When attached to the TACScope, turn the thermal imager upside down and place your left or right

hand through either of the hand straps. Look through the eyepiece on the TACScope to see the

thermal image.

NOTE

When using the TACSCOPE with the thermal imager inverted, the thermal imager's

startup graphics will also be inverted. However, the thermal image will always

maintain its correct orientation.

TACScope Specifications

Power Source: 10-12VDC (supplied by TACSIGHT imager)

Power Consumption: 1.0 W

Power Switch: Controlled by imager power switch

Display Resolution: 320x240 pixels (Imager resolution 160x120 pixels)

Color: Grayscale monochrome

Magnification: 0.85 X on TACSIGHT imager (0.30 X on T3 imager)

Apparent Distance: 8 meters

Eye Relief: 76mm

Water Resistance: IP64

Shock Resistance: 1 Meter drop on concrete

Temperature:

Operating:

-20 - +60 C

Storage: -20 - +80 C

Display Size:

5.44 mm diagonal

Eyepiece Lens: 21.4mm EFL, f/1.18

NOTE

The TACScope cannot be used in conjunction with the TACPort or

HANDLEV

O Accessories.

The external power supply must not exceed 15 VDC. Whatever power supply is used,

the 2.5 mm phone plug should be connected to the TACPort first, before connecting

to the power supply.

CAUTION

If the power requirement of the accessory exceeds 500 mA, an external power

supply MUST be used.

CAUTION

1 2

Inhaltsverzeichnis

Seite 1 - User Manual

Bullard TACSIGHT AccessoriesUser Manualwww.bullard.com TACPort™Bullard offers the TACPort as a power accessory to the TACSIGHTThermal Imager. Electric

Seite 2 - Warranty

Weitere Dokumente für Sicherheit Bullard Tacsight

Um das Dokument anzuzeigen Bullard Tacsight Bedienungsanleitung

Bullard Tacsight Bedienungsanleitung (2 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Bullard Tacsight Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Sicherheit Bullard Tacsight herunter. Bullard Tacsight User Manual Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Sicherheit Bullard Tacsight

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheit Bullard Tacsight